PERSONAL RESTRAINT ESCAPE KIT (PRE-KIT)

The PRE-KIT is a minimalist alternative to the PLAN B+ that reduces the overall cost whilst maintaining the capabilities to deal with various restraints.
These kits are made for units that have completed 'The System' delivered by 4TAC5 and are seeking a unit quantity of kits within a budget constraint.

If you have not completed 'The System' you can still get the most out of this kit by reading the handbooks How to Open Handcuffs Without a Key and Escape!

For carry and concealment the PRE-KIT should be worn to allow for access to the tools when restrained to the front or rear.

The recommended method is to carry inside the waistband (IWB), ideally inside underwear with the Go-Tube located at the groin area and Uber Gulag Shim
installed on the silicone bead retainer at the 6 O'clock position.

Another method of carry to quickly don your PRE-KIT is to wear it horizontally across your torso, under clothing so the Go-Tube hangs below your armpit or around the neck.

- Go-Tube 2.6 (length is the same width as US bank notes)
- 550 IWB/Neck Strap (50 inches, cut to length required from female connector end)
- AHK3-rf (can be installed on GTFO-Wrist-Strap or stored inside Go-Tube)
- Uber Gulag Shim
- Uber Gulag Shim + Stainless Steel Split Ring
- RUSkey (works on Russian BRS-2 handcuffs)
- Optimised Hair-Grip (pre-installed with AHK3-rf, Uber Gulag Shim and RUSkey)
- White LED (Runtime 50 days/1,200+ hours with just one CR2032 battery coin cell)*
- PARAMID 400 High Speed Friction Saw (remove elastic bands and reload using figure of 8 method).
- GTFO-Wrist-Strap

*CR2032 NOT INCLUDED DUE TO SHIPPING RESTRICTIONS. The LED and CR2032 should be carried inside the round end cap.

Options
£34.95 GBP





RUSkey

New for 2022!

Developed by Karl OscarDelta the RUSkey is no bigger than a thumbnail to aid carry and concealment on your person.

The RUSkey works on Russian BRS-2 and other handcuffs that share a similar flat key:

- Czech Alfa-Proj/RALKEM 9921- 9930
- BREN BRNO
- Slovakian Puta/AFG
- Walther 302
- Japan Manchu 331182
- Chinese Anhua HC-13W.

Corrosion resistant 304 Full Hard Stainless Steel that differs from other forms of 304 in that it has been
hard cold rolled to its full hard condition. This increases its fatigue life. In its full hard condition, type 304 stainless steel
has a tensile strength of 185,000 PSI minimum, and a minimum yield strength of 140,000 PSI.

Options
*** 10MAR2022: LIMITED STOCK ***



ADVANCED HANDCUFF KEY (AHK3-rf)

New for 2022!

This is the latest version of the AHK designed to retrofit to the GTFO-Wrist-Strap without the requirement to undo the knots.
So if you already own one of our GTFO-Wrist-Straps you can now add a handcuff key...

To install the AHK3-rf:

  • Simply position the channel of the key over the shock-cord
  • Pull and stretch the shock-cord
  • Insert shock-cord inside the key
  • Release the cord
  • The shock-cord will expand to its normal size inside the key.

    To remove the AHK3-rf:

  • Hold the shock-cord
  • Pull on the key to extract the shock-cord from the channel.
  • Your AHK3 is now ready to use...

    The AHK-rf works just like any other AHK3 to counter the security features found on high security handcuffs (key blocking blade, large keyway pin,
    deep set keyhole etc.) The AHK3 has a full depth slit in the key flag to counter the stainless steel security plate on ASP High Security handcuffs.

    From December 2020 we manufactured the AHK3 with the addition of a groove to indicate the direction of the key-flag when it's inside the key-way.
    This new version has been in circulation since January 2021. The AHK-rf also features the groove.

    Note: Where the AHK3 is sold as the 'Delta Key' it will be the older style AHK3 without the groove and channel.

    The AHK3 works on the following handcuffs plus more that share the common key-way:

    - ALCYON
    - ASP
    - CLEJUSO
    - HIATTS
    - KYOUNG CHANG
    - PEERLESS
    - RALKEM
    - RUSSIAN BRS-1
    - SMITH & WESSON
    - TCH
    - UZI
    - WALTER
    - YUIL

    The AHK3 also operates handcuffs that have a bent pin in the keyway that would otherwise block a standard handcuff key.

    Very little pressure is required to operate handcuffs with a key - never force a key to turn!
    'Tactical' handcuff keys are prone to breaking when such excessive stress/torque is applied.
    This is a known issue with polymer handcuff keys that can result in a blocked keyway.
    If the AHK breaks it has been designed to fragment into small parts that can be shaken free from the working parts,
    so it should not block the keyway and therefore allow for a back-up key to be used.
    When using the AHK we recommend that you use it to 'pick and sweep' the lock, taking care to feel for the
    movement of the working parts. Gently rocking and tilting the key works best for some handcuffs and altering the depth
    works for others. Attaching anything to the AHK to assist with turning the key can result in excess torque being applied.

    £10.00 GBP Special Price £8.00 GBP/each




    AHEK

    If you Google search images 'CHINESE POLICE HANDCUFFS' you will find pictures of the ANHUA Handcuffs HC-01W and HC-19W.
    These handcuffs have a rotating wheel that prevents shimming and they also require a unique handcuff key making them hard to bypass without the key.

    The story goes that the USA supplied some old WW1 surplus Harrington and Richardson Model 123 handcuffs to the Chiang Kai Chek
    regime in their struggle with Mao Tse-Tung and when they ran out the Chinese copied them and the rest is history...

    Designed by Karl OscarDelta the AHEK works just like a key to operate the HC-01W and HC-19W handcuffs when single or double-locked.
    The keys are double-ended and knurled for easy operation. Just insert into key-way and turn clockwise.
    The key can be attached to the APEK with our R Clip (not included), stored inside the Plan B or hidden on your person elsewhere.

    Note: The AHEK is replicating the function of one of the largest handcuffs keys that features a big handle to assist with turning under spring tension.

    Follow these steps to effectively use the AHEK:

  • Insert the AHEK into the key-way tube
  • Slowly rotate the AHEK to carefully locate the triangle stud
  • Push the AHEK firmly down to ensure it remains seated over the tringle stud
  • Turn the AHEK clockwise and push in the ratchet arm (use your leg/body)
  • This additional step will cause the handcuffs to release



    ANHUA Handcuffs HC-01W and HC-19W are made in China, sold in the UK and Germany - they are out there, somewhere!

    £2.50 GBP




    LOADOUT 2065

    Developed by Karl OscarDelta the LOADOUT 2065 has been designed to fit the EBUTOG.

    The loadout contains the latest tools for defeating restraints and methods of confinement in a compact package.

    This is the current kit that is issued to students and instructors during advanced training by 4TAC5.
    On completion of the course students and instructors will swap out the loadout used for training and replace it with a fresh loadout.

    The LOADOUT 2065 can also be concealed inside the boot/trunk of your operational/personal vehicle ready for deployment.

    Contents:

  • PARAMID 325 HIGH SPEED FRICTION SAW
  • SAD-TOOL + RAKE & WRENCH
  • ANHUA HANDCUFF ESCAPE KEY
  • DARBY TUBE
  • COMBINATION PADLOCK BYPASS TOOL
  • OPTIMISED HAIR-GRIP
  • RGB LED DIODE WITH COVERT NOSE
  • CR 2032 LITHIUM BATTERY COIN CELL (will also fit Micro-SQ-Light)*
  • UBER GULAG SHIM WITH STAINLESS STEEL SPLIT RING
  • AHK3-rf (for adding to any GTFO-Wrist-Strap)

    *The CR2032 battery has been removed as it can not be sent via Royal Mail or DHL.

    For carry and concealment with the EBUTOG we recommend adding the IWB STRAP 3.0


    The LOADOUT 2065 has become so popular with select units that we are now including a FREE Micro-SQ-Light with all orders.
    We have also included the Mini Zipper Bag (MZB53) - so you're good to go!

    Options


    PLAN B+

    Developed by Karl OscarDelta the PLAN B+ is a Fast Track Counter Custody Kit that can be donned or removed in seconds so it can be carried & concealed
    on your person, regardless of what you are wearing. It is also very comfortable to wear so you'll easily forget that you're wearing it (passive).
    Full access to the tools is possible if you are restrained to the front or rear and need to put 'Plan B' into action!

    Contents:

    IWB STRAP 3.0 featuring a shock-cord strap with a type B breakaway connectors for inside waistband carry & concealment.

    UBER GULAG SHIM 3.0 with stainless steel split ring installed on shock-cord waist strap with silicon retainers
    for access when restrained to the front or rear.

    PARAMID 325 HIGH SPEED FRICTION SAW developed by the 4TAC5 Mobile Training Team, SERE and CAC Instructors.
    The overall length, size of the foot-loops and the addition of a plastic feeder allow for this tool to be quickly deployed and used
    immediately to defeat non-metallic restraints should you be restrained to the front or rear.

    SAD-TOOL+RAKE 3.0 (Special Activities Development Tool) designed to defeat various handcuffs and restraints
    from around the world. Can also be used to open basic padlocks.

    TENSION WRENCH for applying tension to the lock as you rake and pick.

    COMBINATION PADLOCK BYPASS TOOL 2.0 This is probably the smallest bypass tool for Covert Method of Entry (CME) in the world.
    Designed for carry and concealment this tool can be used to quickly open common Combination Padlocks such as the Master Lock 178D
    without the need for the set combination. Simply insert the tip of the tool into the left side of wheel #2 at a slight angle and then
    push down (images to follow soon). Some padlocks require the shackle to be depressed and released and others can be pulled open
    once as you push down on the tool. The tool material is marine grade 316 stainless steel.

    ANHUA HANDCUFF ESCAPE KEY The AHEK works just like a key to operate the HC-01W and HC-19W handcuffs when single or double-locked.
    The keys are double-ended and knurled for easy operation. Just insert into key-way and turn clockwise if single-locked and anti-clockwise
    if double-locked. The key can be attached to the APEK with our R Clip (not included), stored inside the Plan B or hidden on your person elsewhere.

    MICRO STRIKER BEAD (installed on shock-cord waist strap). Measuring just 6.75mm x 3.25mm this is our smallest glass beaker
    for tempered glass windows. Using the Mohs scale, which is used to test hardness, the score achieved by MSB is 9.
    To put this into context, the only thing that has a higher score than tungsten carbide is a diamond, which manages to score a rating of 10.
    With a mineral hardness of 9.0 MOHS the MSB will break tempered glass windows with very little effort.

    DARBY TUBE push 'n pull to open vintage handcuffs that feature a threaded key-way.

    HAIR-GRIP can be used to replicate the function of the SAD-Tool and advanced escape techniques.

    RGB LED DIODE WITH COVERT NOSE replaces chemical light sticks for better light control.

    CR 2032 LITHIUM BATTERY COIN CELL for use with LED Diode, stored inside EBUTOG Cap (remove O-Ring, insert coin cell, replace O-Ring),
    can also be used as a battery replacement for the Micro-SQ-Light)*

    *This CR2032 battery has been removed as it can not be sent via Royal Mail or DHL.

    Note: All produucts that end with a + indicate that you will receive the latest version/upgrade that may differ slightly from the one shown.

    Options







    APEK 5.2 / APEK+

    The Advanced Personal Escape Kit allows for essential restraint escape tools to be neck carried out of sight but
    ready for immediate deployment. A shirt or polo shirt will aid concealment. When travelling it is not necessary to
    remove this necklace when passing through airport security. This is probably the one item of 'escape equipment' that
    you will have with you 24/7 regardless of what you are wearing or doing. After time it will become a carry habit,
    very much like wearing a watch - when you do forget to put it on you will know the difference!

    APEK 5.2 Specification:

    Tech 205 Cord (Escape Necklace) for use as a friction saw to cut through non-metallic restraints when restrained to the front.

    There is no preparation required (knots to tie etc.) ...

    - Feed one end of the cord through the restraint until it reaches one of the knots.
    - Place the foot loops over the toe part of your shoes or if barefoot between the big toe and increase the tension of the cord so it
    positions itself on the lower part of the restraint to avoid friction injuries.
    - Now move your feet in a slow pedal motion and gradually build up speed.
    - The heat from the friction will burn through the restraint.
    - For oil treated natural rope such as hemp (or if submerged under water) little or no friction will be generated; however the knots will cut through the material.

    Tip: For silently removing cable-ties and nylon rope you do not need to use the cutting knots. Keep within the two knots to keep the noise to a minimum.

    Advanced Handcuff Key retrofit (AHK3-rf) designed to counter additional security features found on some handcuffs (key blocking blade, large key hole pin,
    deep set keyhole etc.)

    R Clip When installed with the Advanced Handcuff Key the R Clip can improve manual dexterity.

    Uber Gulag Shim 3.0 This is the latest version (DEC2018) that is slightly slimmer for the American UZI handcuffs.
    Works on British TCH, Czech ALFAproj, Polish KEL-MET, Russian BRS-2, Russian CROT and Spanish ALYCON.

    Micro Striker Bead (MSB) for breaking tempered glass windows (car side windows).
    Concealed inside the plastic breakaway connector the MSB is hidden until you require it. To deploy you pull on the cord either side of the
    breakaway connector to pull apart. The MSB is seated inside the the female part. Simply slide the plastic female part down the cord and
    past the first cutting knot whilst holding onto the end of the cord between your thumb and forefinger.
    The MSB will eject from the connector. Slide the MSB to the diamond stopper knot.
    Now wrap the cord around your hand and leave about 12 inches of cord hanging free with the MSB on the end.
    Swing the MSB towards the glass - very little force is required as the mineral hardness of the MSB (9.5 MOHS)
    is greater than glass (will punch a hole in a glass bottle!). You can use this to escape from a car or rescue persons from a car
    (the friction saw will cut seat-belts). To close the connectors simply push and twist them together by hand. Do not use a tool (pliers etc.)
    as this may cause damage to the connectors.

    APEK+ Specification:

    As above but with the MICRO-SQ-LIGHT installed.



    Our Technora Escape Necklaces and Advanced Personal Escape Kits have a diamond stopper knot as shown above.
    If it does not feature the diamond stopper knot it is not our product - it is a copy!

    Options

    Note: All produucts that end with a + indicate that you will receive the latest version/upgrade that may differ slightly from the one shown.




    FAST TRACK COUNTER CUSTODY KIT+ (FT-CCK+)

    This is the latest FT-CCK developed for individuals that are prone to capture and now available with an instruction handbook.

    The FT-CCK+ has been developed and designed to accelerate the progress of escaping restraints and custody with tools that provide
    for more rapid results than usual. Many tools have more than one function. To get the most out of your FT-CCK+ (how to carry, conceal and deploy)
    we recommend the handbook Escape!

    With training, skills and knowledge the FT-CCK4.5 contains essential tools for dealing with various methods of restraint and captivity.

    Contents:

  • APEK+ - Technora Escape Necklace installed with AHK3-rf, Uber Gulag Shim 2.0, R Clip, Micro Light Stick, Micro Striker Bead
    and Micro-SQ-Light.
  • Plan B+ installed with the following...
  • SAD Tool+Rake
  • Tension Wrench for use with Rake
  • Paramid 325 High Speed Friction Saw
  • IWB Strap 3.0 with safety type B breakaway connector
  • Uber Gulag Shim 2.0 + 120lb Stainless Steel Split Ring installed on IWB Strap
  • Micro Striker Bead installed on shock-cord waist IWB Strap
  • RGB LED Diode
  • CR2032 Battery Coin Cell (stored inside cap)*
  • Darby Tube
  • Optimised Hair-Grip
  • Anhua Handcuff Escape Key 2.0
  • Combination Padlock Bypass Tool 2.0
  • GTFO-Wrist-Strap with AHK3-rf installed
  • Supplied in a PVC Mesh Zipper Case

    *This CR2032 battery has been removed as it can not be sent via Royal Mail or DHL.

    Note: All produucts that end with a + indicate that you will receive the latest version/upgrade that may differ slightly from the one shown.

    £90.00 GBP




    SOH HACK PACK 2020.9

    Developed by Karl OscarDelta the SOH HACK PACK 2020.9 contains the following items:

  • Clear Zipper Case
  • Paracord
  • Small Cable/Zip Tie
  • 3 x Hair-Grips
  • 3 x Hair-Clips
  • Luggage Tag LTX1
  • 13 inches of Scapa (Sniper) Tape
  • High Tensile Stainless Steel Safety Pin
  • Advanced Handcuff Key AHK3-rf
  • 2 x Uber Gulag Shims
  • 2 x Heavy Duty Cable/Zip-Tie

    This is the kit used in the handbook Escape! to demonstrate the improvised friction saw, tool carry and concealment.

    Software and hardware is a general term that 4TAC5.COM sometimes use to describe the Progressive Restraint Escape System ('the system'). Software is an
    ordered sequence of instructions for defeating restraints that is committed to memory becoming an integral part of the system. Hardware is best described as a
    device that can be physically touched. Handcuffs, keys, shims, cable-ties, zip-ties, friction saws, duct tape are all examples of hardware. Software and hardware
    interact with one another: software tells hardware which tasks it needs to perform.

    Unlike hardware, software is extremely flexible, allowing it to be continuously updated and modified.

    When training to escape handcuffs or any restraint for that matter and you encounter a problem, the first thing you should try to do is determine if the
    problem is with the software or with the hardware. How you make that determination depends on the problem you're experiencing, but it often involves
    ruling out one or the other via testing.

    We recommend that you learn how to reproduce the 'manufactured' tools and replicate their function with basic materials as listed in the SOH HACK PACK.
    For information that will further expand your knowledge, skills and understanding (software) for defeating various restraints with limited resources
    select the handbook HOW TO OPEN HANDCUFFS WITHOUT A KEY (HTOHWAK) from the drop down menu...

    Options
    Save £5.00 GBP when you purchase the handbook How to open handcuffs without a key...
    Before you purchase consider our OD TRIPLE THREAT PACK



    SOH RELOAD PACK



    You can now get the quality hair-grips and hair-clips that we use in our kits.

  • Hair-Grips x 3 (same ones used in our Fast Track Counter Custody Kit and SOH Hack Pack)
  • Hair-Clips x 3 (these are high tensile, not the cheap bendy type!)

    £2.95 GBP








    APEK-V521

    The APEK-V521 is a variant of the APEK 5.2 that allows for you to carry and conceal tools for defeating restraints and covert methods of entry.

    TECHNORA ESCAPE NECKLACE
  • AHK3-rf
  • R-CLIP
  • SAD-TOOL WITH THE TRIPLE HUMP RAKE PERMANENTLY INSTALLED WITH A BRASS RIVET
  • MODIFIED TENSION TOOL ROTATED TO LAY FLAT ON THE APEK

    £43.50 GBP

    If you already own a Technora Escape Necklace and SAD-Tool 3.0 you can add the tools from the drop-down menu to create your own APEK-V521.

    Options



    T200 HIGH SPEED FRICTION SAW (2 PACK)

    The T200 High Speed Friction Saw has been developed by the Karl OscarDelta , 4TAC5 Mobile Training Team, SERE and CAC Instructors.

    The overall length, size of the foot-loops and the addition of a plastic feeder allow for this tool to be quickly deployed and used
    immediately to defeat non-metallic restraints should you be restrained to the front or rear.

    Sold in pairs so you have one for training and one for your escape kit (the one used for training can be carried and concealed as a back-up).


    £10.00 GBP (2PK)



    SAD-TOOL 3.0

    Designed by 4TAC5.COM and manufactured in the UK by OscarDelta SPD.

    The Special Activities Development Tool is corrosion resistant 304 Full Hard Stainless Steel that differs from other forms of 304 in that it has been
    hard cold rolled to its full hard condition. This increases its fatigue life. In its full hard condition, type 304 stainless steel
    has a tensile strength of 185,000 PSI minimum, and a minimum yield strength of 140,000 PSI.

    With the appropriate skills, knowledge and understanding can be used to facilitate escape from unlawful restraints and captivity
    using non-destructive methods. It is recommended that you have one spare SAD Tool that can be used for 'development' to explore
    the capabilities and potential applications of the tool. These 'special activities' require access to a set of handcuffs,
    heavy duty cable-ties and a budget padlock (pin and cylinder that locks on one side of the shackle).

    With practice you will be able to remove handcuffs without a key (single and double/transport lock) and exploit weaknesses in
    the handcuff design to bypass the double-lock mechanism to allow for shimming etc. These methods can be used on so called 'high security'
    handcuffs that have additional features that would normally require a unique or non-standard key to operate.

    With continued practice it works quicker than a key for taking off the double-lock, particularly when handcuffed to the rear.

    You can also use the tool to open a budget padlock without a key and remove cable-ties using non-destructive methods.

    *** THE SAD-TOOL 3.0 CAN BE INSTALLED ON THE TECHNORA ESCAPE NECKLACE / APEK ***

    Quanitity




    HIGH TENSILE STAINLESS STEEL SAFETY PIN

    These are premium quality British made rust proof safety pins manufactured from high tensile stainless steel spring wire.
    They will not bend or deform easily so can be used to perform some of the functions of the SAD Tool.

    A silicone retainer has been installed to allow for various carry and concealment options for Bogota Lock Picks and our SAD Tool.


    £1.50 GBP







    UBER GULAG SHIM 3.0

    The Uber Gulag Shim 3.0 is a combination of the original Uber Shim and Gulag Shim.

    Developed by Karl OscarDelta and precision engineered in the UK the unique length, width and thickness ensures it will
    work with a wider selection of handcuffs that would otherwise resist or fail to shim with other commercially available shims.

    These include American UZI, British TCH, Czech ALFAproj, Polish KEL-MET, Russian BRS-2, Russian CROT and Spanish ALYCON.

    When using the Uber Gulag Shim the silky smooth operation almost makes shimming effortless!

    In additional to its unique design features the Uber Gulag Shim is 304 Full Hard Stainless Steel that differs
    from other forms of 304 in that it has been hard cold rolled to its full hard condition. This increases its fatigue life.
    In its full hard condition, type 304 stainless steel has a tensile strength of 185,000 PSI minimum, and a minimum yield strength
    of 140,000 PSI. So unlike spring steel the Uber Shim will not easily snap when bent so it is possible to reshape and straighten.

    - Stainless Steel
    - Rust Resistant
    - Silent Operation.

    Tip: Do not force the shim as you will bend it! Always start shimming where the ratchet arm enters, there should be a small gap,
    insert the tip of the shim and at the same time slightly push in the ratchet arm to assist (push assist).
    Only do this if the shim is moving between the ratchet and pawls (teeth) otherwise you risk over-tightening the handcuffs.
    In the event that shimming does not work it is possible that the handcuffs are either double-locked or have security features to prevent shimming.

    AHK3 and R Clip NOT included.

    Not all shims are created equal...

    - Various shims vs Uzi handcuffs (YouTube video).

    - Various shims vs Russin BRS-2 handcuffs (YouTube video).


    £12.50 GBP (4 PACK)



    TECHNORA ESCAPE NECKLACE

    This is a covert necklace designed for use as a friction saw to cut through non-metallic restraints when restrained to the front.

    There is no preparation required (knots to tie etc.) ...

    - Feed one end of the cord through the restraint until it reaches one of the knots.
    - Place the foot loops over the toe part of your shoes or if barefoot between the big toe and increase the tension of the cord so it
    positions itself on the lower part of the restraint to avoid friction injuries.
    - Now move your feet in a slow pedal motion and gradually build up speed.
    - The heat from the friction will burn through the restraint.

    Tip: For silently removing cable-ties and nylon rope you do not need to use the cutting knots.
    Keep within the two knots to keep the noise to a minimum.

    Tip: For silently removing cable-ties and nylon rope you do not need to use the cutting knots. Keep within the two knots
    to keep the noise to a minimum. Add a cutting knot to the middle of the necklace for natural rope and cord (hemp etc.)

    The Technora Escape Necklace also features the Micro Striker Bead (MSB) for breaking tempered glass windows
    It is concealed inside the plastic breakaway connector the MSB is hidden until you require it.
    To deploy:
    Pull on the cord either side of the breakaway connector to pull apart. The MSB is seated inside the the female part.
    Simply slide the plastic female part down the cord and past the first cutting knot whilst holding onto the end of the cord between your thumb and forefinger.
    The MSB will eject from the connector. Slide the MSB to the diamond stopper knot.
    Now wrap the cord containing the tools around your hand and leave about 12 inches of cord hanging free with the MSB on the end.
    Swing the MSB towards the glass - very little force is required as the mineral hardness of the MSB (9.5 MOHS)
    is greater than glass (will punch a hole in a glass bottle!). You can use this to escape from a car or rescue persons from a car
    (the friction saw will cut seat-belts). To close the connectors simply push and twist them together by hand. Do not use a tool (pliers etc.)
    as this may cause damage to the connectors.

    4 x Silicone Retainers fitted as standard to carry the tools (Light Sticks, Bogota Picks, Shims, Modified Hair Grip, Handcuff keys etc.)

    *** CONSIDER ADDING THE SAD-TOOL 3.0, AHK3 AND R CLIP TO MAKE THIS AN UPGRADED ADVANCED PERSONAL ESCAPE KIT ***



    Our Technora Escape Necklaces and Advanced Personal Escape Kits have a diamond stopper knot as shown above.
    If it does not feature the diamond stopper knot it is not our product - it is a copy!

    Watch it in action! MSB deployed from APEK Necklace - YouTube Video

    £12.50 GBP




    TECHNORA ESCAPE NECKLACE COLORIZED

    All the features of the original Technora Escape Necklace but with random coloured silicone retainers and breakaway connectors...

    *** CONSIDER ADDING THE SAD-TOOL 3.0, AHK3 AND R CLIP TO MAKE THIS AN UPGRADED ADVANCED PERSONAL ESCAPE KIT ***



    Our Technora Escape Necklaces and Advanced Personal Escape Kits have a diamond stopper knot as shown above.
    If it does not feature the diamond stopper knot it is NOT our product - it is a copy!

    £12.50 GBP






    R CLIP

    When installed with the Advanced Handcuff Key our stainless steel R Clip can improve manual dexterity.

    £0.50 GBP






    STAINLESS STEEL SPLIT RING

    These are the same split rings that we use with our Uber Gulag Shims when installed on the Plan B.
    They assist with dexterity, retention and allow for the full depth of the shim to be used.

    £1.00 GBP (4 pack)


    HOW DOES PAYPAL WORK? CLICK ON IMAGE BELOW.

    PayPal Acceptance Mark

    PROBLEM WITH PAYPAL?

    SOME CUSTOMERS EXPERIENCE AN ISSUE WITH THE PAYPAL SHOPPING CART.
    IF YOU ARE UNABLE TO COMPLETE THE TRANSACTION YOU CAN SEND THE TOTAL AMOUNT VIA THE PAYPAL LINK BELOW.
    https://www.paypal.me/disruptivethinking

    ONCE YOU HAVE MADE PAYMENT PLEASE SEND AN EMAIL WITH THE FOLLOWING INFORMATION:

    - THE TRANSACTION ID
    - LIST OF ITEMS REQUIRED
    - DELIVERY ADDRESS.

    WE WILL THEN CONFIRM YOUR ORDER HAS BEEN RECEIVED.
    YOUR ORDER WILL THEN BE PROCESSED AND SHIPPED WITHIN 5 WORKING DAYS.

    N.B. IF USING FIREFOX MOZILLA (MAY WORK WITH OTHER BROWSERS) YOU CAN TRY THIS QUICK FIX...

    OPEN MENU (3 BARS ICON) TOP RIGHT CORNER.
    SELECT: OPTIONS > PRIVACY & SECURITY > COOKIES AND DATA > MANAGE DATA > REMOVE ALL > SAVE CHANGES

    OPEN UP A NEW TAB AND TRY AGAIN. THE PAYPAL BUTTON SHOULD NOW WORK.




    MINIMUM ORDER £12.50 GBP
    FREE SHIPPING DOES NOT INCLUDE TRACKING.
    DELIVERY WILL BE VIA ROYAL MAIL 1ST CLASS/INTERNATIONAL
    WE CAN PROVIDE PROOF OF POSTAGE IF REQUIRED.
    WE NORMALLY DISPATCH WITHIN 5 WORKING DAYS.
    WE DO NOT SEND ORDER STATUS NOTIFICATIONS UNLESS THERE IS DELAY PROCESSING YOUR ORDER.
    PLEASE CHECK YOUR PAYPAL ACCOUNT FOR ORDER STATUS.

    FOR FURTHER INFORMATION PLEASE ENSURE YOU READ OUR DELIVERY INFORMATION




    FOR A TRACKED DELIVERY SERVICE USE THE 'ADD TO CART' BUTTON BELOW.

    THE TRACKING NUMBER INFORMATION WILL BE ADDED TO YOUR PAYPAL TRANSACTION.
    FOR INTERNATIONAL ORDERS WE WILL USE ROYAL MAIL TRACKED AND SIGNED.
    FOR DOMESTIC ORDERS (UK MAINLAND) WE WILL USE ROYAL MAIL SPECIAL DELIVERY.

    £7.50 GBP


    OscarDelta SPD | services@oscardelta.co.uk | ƃuᴉʞuᴉɥʇ ǝʌᴉʇdnɹsᴉp | Copyright © 2006 - 2022. All Rights Reserved.

    Home